OPERATOR’S MANUAL MODEL 6300 COULTER CART YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777
10ASSEMBLY INSTRUCTIONS STEP 7. Mount a set of clamp plates to the toolbar at each chalk mark using 4) ½” x 8” bolts, 2) shank clamp castings, and ½”
11ASSEMBLY INSTRUCTIONS STEP 8. Insert the locking collar into the pivot casting of the coulter assembly. Slide the shorter offset end of the shank
12ASSEMBLY INSTRUCTIONS STEP 10. Slide the shank up through the clamp castings and retain by installing a 5/16” x 2 ½” cotter pin in the top hole of
13ASSEMBLY INSTRUCTIONS Toolbar Hanger Assembly STEP 12. Install the 2 ½” x 8” hydraulic cylinder base end and clevis to the toolbar hanger using the
14ASSEMBLY INSTRUCTIONS Optional Second Toolbar STEP 1. Hydraulically lower the coulter cart so that the coulters are touching a hard, level surface.
15ASSEMBLY INSTRUCTIONS Optional Toolbar Gauge Wheels STEP 1. Attach the gauge wheel bracket near the end of the front toolbar using 2) ¾” x 5” x 6 ½
161OPERATION PREPARING THE TOOLBAR Drawbar Height The Yetter model 6300 coulter cart is designed to operate on tractors with drawbar heights from 18”
17OPERATION Hydraulic Hook Up Continued 3. Connect the two hoses from the transport lift system to the tractor. The hydraulic hoses are provided wit
18OPERATIONMARKER HYDRAULICS Row marker may be plumbed into the cart transport lift system. STEP 1. Plumb the “LIFT/RAISE” hydraulic hose of the mark
19OPERATIONATTACHING IMPLEMENT WARNING: Be sure the attached implement is securely locked in the hitch of the cart before operating. Failure to heed
2FOREWORD You’ve just joined an exclusive but rapidly growing club. For our part, we want to welcome you to the group and thank you for buying a Yette
20OPERATIONFIELD OPERATION WARNING: Do not allow children to operate this equipment. Do not allow riders on the tractor. Failure to heed may result
21OPERATION WARNING: Never clean, lubricate or adjust a machine that is in motion. Failure to heed may result in serious personal injury or death. C
22PARTS IDENTIFICATION KEY QTY. PART NO. DESCRIPTION 1. 4 6600-219 INSERT ROLLER 2. 2 6600-202 LIFT WHEEL INSERT W.A.
23PARTS IDENTIFICATION _____________________________________________________________ KEY QTY. PART NO. DESCRIPTION 1. 4 2570-4
24PARTS IDENTIFICATION KEY QTY. PART NO. DESCRIPTION 1. 1 6300-315 15’ TOOLBAR 1 6300-320 20’ TOOLBAR 2. 2
25PARTS IDENTIFICATION
26PARTS IDENTIFICATION
27PARTS IDENTIFICATION
28PARTS IDENTIFICATION KEY QTY. PART NO. DESCRIPTION 1. 4 2570-643 ¾ X 5” X 6 ½” U-BOLT ZYD. 2. 2 6300-213
29PARTS IDENTIFICATION
3SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study these precautions carefu
30PARTS IDENTIFICATION
311PARTS IDENTIFICATION DOWN PRESSURE REGULATING VALVE KIT The down-pressure regulating valve kit replaces the two “T” fittings, in the middle of the
32SPECIFICATIONS REAR VIEW Hydraulic Cycle Time Rear Lift Cylinders: Tractor at 1500-RPM Hydraulic Outlets set at fast (Rabbit) Full Cycle Time is: 4.
336600-181 LIGHT KIT ASSEMBLY 1. Mount amber lights, one on each side, in the top slot of the warning light bracket. The red light is mounted on the
346600-180 SAFETY CHAIN KITSUMMARY OF ADJUSTMENTS AND SETTINGS COMPONENT Cart and Drill Drill press wheels SETTING Leveling Alignment of coulters an
35 TROUBLESHOOTINGProblem Coulter cart will not lower. Cart frame raises or lowers slowly. Erratic or uneven lift. Coulter cart will not raise. Attac
36Our name Is getting knownJust a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on a program of expansion
4ASSEMBLY INSTRUCTIONS GENERAL INFORMATION Examine all equipment carefully for damage or shortages. Lubricate all bearings and moving parts as assembl
5ASSEMBLY INSTRUCTIONSWARNING: Never work under the equipment while in a raised position without using safety lockups. Failure to do so may lead to
6ASSEMBLY INSTRUCTIONS Hanger Bar STEP 1. Attach the hanger bar assembly to the 8” x 8” center frame using the 4) 1” x 11” hex bolts and 1” hex lock
7ASSEMBLY INSTRUCTIONS Attaching the 5” x 5” coulter toolbar to the hanger bar STEP 3. A coulter will be mounted on the cart directly in line with ea
8ASSEMBLY INSTRUCTIONS LOCATIONS FOR OFFSET BRACKETS
9ASSEMBLY INSTRUCTIONS STEP 5. Attach the 2) 6300-207 cylinder lugs to the coulter toolbar using ¾” u-bolts and ¾” lock nuts. Locate the inside edge
Comments to this Manuals