Yetter 2000 Series Vertical Tillage Tool (V.T.T.) User Manual

V.T.T. ™ 2000 SERIES VERTICAL TILLAGE TOOL ™ SET-UP AND PARTS MANUAL YETTER MANUFACTURING CO. FOUNDED 1930 Colche

10 ASSEMBLY INSTRUCTIONS Step 8. Clamp the depth adjustment to the toolbar. Torque to 300 ft/lbs. Step 9. Attach the 4” X 12” hydraulic cy

11 ASSEMBLY INSTRUCTIONS Step 10. Install cylinder stops: 4 X 12 cylinder, toolbar lift. IMPORTANT: Install 5” of 2000-507 cylinder st

12 ASSEMBLY INSTRUCTIONS Step 11. Attach the parallel arms to the Bridge Hitch.

13 ASSEMBLY INSTRUCTIONS Step 12. Unfold the toolbar from the freight position. Attach the center bracket to the toolbar.

14 ASSEMBLY INSTRUCTIONS Step 13. Attach the toolbar to the Bridge Hitch.

15 ASSEMBLY INSTRUCTIONS Step 14. Attach the hydraulic cylinder to the toolbar assembly.

16 ASSEMBLY INSTRUCTIONS Step 15. Install cylinder stops, 2000-511 (2” cylinder rod) to limit the toolbar wing folding.

17 ASSEMBLY INSTRUCTIONS Step 16. 2000-509 Cylinder Stop; Cut off length to 13”. Step 17. Install the cylinder stops on the wing fold cylind

18 1ASSEMBLY INSTRUCTIONS Step 18. Install the wing fold stops to the toolbar. Do not fully tighten, will need to be adjusted later. Hyd

19 ASSEMBLY INSTRUCTIONS Step 19. Install the hydraulic hoses, fitting, and valves.

2 FOREWORD You’ve just joined an exclusive but rapidly growing club. For our part, we want to welcome you to the group and thank

20 ASSEMBLY INSTRUCTIONS Step 20. Attach the valve bracket to the Bridge Hitch. Attach the valve to the bracket.

21 ASSEMBLY INSTRUCTIONS Step 21. Measure the toolbar to find the centerline. Mark the toolbar for clamp plate locations as shown in the examp

22 ASSEMBLY INSTRUCTIONS Step 22. Install the roll pin to the shank. Insert the locking collar into the coulter swivel casting. From the bottom

23 ASSEMBLY INSTRUCTIONS Step 24. Attach the blades and hub cap straps to the coulter assembly using the carriage bolts, lock washers and nuts.

24 ASSEMBLY INSTRUCTIONS Step 25. Attach the tank cradle to the mount brackets using the 5/8” X 4” bolts and lock nuts. Step 26. Attach t

25 ASSEMBLY INSTRUCTIONS Step 27. Install the plug fittings into the tank – use thread tape or thread compound. Attach the SMV decal to the tan

26 ASSEMBLY INSTRUCTIONS Step 28. Set the tank into the cradle and secure with the straps.

27 ASSEMBLY INSTRUCTIONS Step 29. Attach the 2000-290 weight bracket to the toolbar using the (8) ¾ “ X 10” bolts, (4) mount plates and (8) ¾” l

28 1OPERATION WARNING: Do not allow children to operate this equipment. Do not allow riders on the tractor or implement. Failure to heed may res

29 1 OPERATION Hydraulic Hook Up DANGER: Inspect and replace worn or frayed hydraulic hose. Keep all connections tight, escaping hydraulic

3 SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study

30 OPERATION PREPARING V.T.T. TM FOR TRANSPORT STEP 1. Remove wing flex cylinder stops from the 5 X 16 hydraulic fold cylinders, place in storag

31 OPERATION PREPARING V.T.T. FOR FIELD STEP 1. Unfold toolbar STEP 2. Install wing flex cylinder stops onto 5 X 16 hydraulic fold cylinders ST

32 OPERATION COULTER BLADE DEPTH ADJUSTMENT To change to the operating depth of the coulter blades, the adjustment is to be pinned in one of seven

33 1111 MAINTENANCE WARNING: Never clean, lubricate or adjust a machine that is in motion. Failure to heed may result in serious personal injury o

34 PARTS INDENTIFICATION

35 PARTS INDENTIFICATION

36 PARTS INDENTIFICATION

37 PARTS INDENTIFICATION

38 PARTS INDENTIFICATION

39 PARTS INDENTIFICATION

4 TABLE OF CONTENTS PAGE FORWARD………………………………………………………….……………2 WARRANTY…………………………………………………………….………..2 SA

40 PARTS INDENTIFICATION

41 PARTS INDENTIFICATION

42 PARTS INDENTIFICATION

43 PARTS INDENTIFICATION

44 PARTS INDENTIFICATION

45 PARTS INDENTIFICATION

46 PARTS INDENTIFICATION

47 PARTS INDENTIFICATION

48 PARTS INDENTIFICATION

49 PARTS INDENTIFICATION

5 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION Examine all equipment carefully for damage or shortages. Lubricate all bearings and moving parts as

50 PARTS INDENTIFICATION

51 PARTS INDENTIFICATION

52 PARTS INDENTIFICATION

53 PARTS INDENTIFICATION

54 PARTS INDENTIFICATION

55 TROUBLESHOOTING Problem Cause Solution Setting coulter depth equally Frame not set correctly Ensure

56 Our name Is getting known Just a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on a pr

6 ASSEMBLY INSTRUCTIONS Step 1. Attach axle assembly to the Bridge Hitch Frame. Bolt torque 305 ft/lbs. Attach SMV bracket (not used with optiona

7 ASSEMBLY INSTRUCTIONS Step 3. Level the Bridge Hitch frame. Install the hitch. Torque bolts to 670 ft/lbs.

8 ASSEMBLY INSTRUCTIONS Step 4. Install the safety chain and hose holder. Torque to 300 ft/lbs. Step 5. Install the jack assembly to the Br

9 ASSEMBLY INSTRUCTIONS Step 6. Assemble the depth adjustment hardware. Step 7. Install the depth adjustment bar to the Bridge Hitch.