ALL STEER MODEL 2000 HIGH CAPACITY CART OPERATOR’S MANUAL PART IDENTIFICATION 2565-726_REV_D 12/11 YETTER MANUFACTURING CO. F
10 ASSEMBLY INSTRUCTIONS Step 6A. Install light brackets to rear axle using ¾” x 7 x 7 u-bolt, and hex nut. Also, attach the red reflectors at th
11 ASSEMBLY INSTRUCTIONS Step 6C. I704-22 Step 7. Install lights to light brackets using hardware listed above.
12 ASSEMBLY INSTRUCTIONS Step 8. Install safety light wiring harness. Plumbing - No plumbing is supplied by Yetter Manufacturing Inc. Co. - SUGG
13 OPERATION DO NOT TOW THE ALL STEER OVER 25 MPH! THE TOW VEHICLE NEEDS TO BE ABLE TO SAFELY HANDLE A MINIMUM OF 24,000 LBS. Maximum carrying ca
14 OPERATION FIELD LOCATION TRANSPORT LOCATION BE CERTAIN THE PINS ARE ENGAGED IN THE HOLES OF THE INNER STEERIN
15 LUBRICATION MAINTENANCE Check hub for bearing play yearly. Oil ball sockets to prevent corrosion, seizure and wear. Replace all worn bolts.
16 PARTS IDENTIFICATION
17 PARTS IDENTIFICATION MANUFACTURED 3-04 TO 6-04
18 PARTS IDENTIFICATION MANUFACTURED 3-04 TO 6-04
19 PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05
2 FOREWORD You’ve just joined an exclusive but rapidly growing club. For our part, we want to welcome you to the group and thank you
20 PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05
21 PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05
22 PARTS IDENTIFICATION MANUFACTURED 08-04 TO 08-05
23 PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07
24 PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07
25 PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07
26 PARTS IDENTIFICATION MANUFACTURED 08-05 TO 07-07
27 PARTS IDENTIFICATION REAR AXLE ASSEMBLY MANUFACTURED 03-04 TO 07-07
28 PARTS IDENTIFICATION FRONT AXLE ASSEMBLY MANUFACTURED 03-04 TO 07-07
29 PARTS IDENTIFICATION UPDATED 06/10/08
3 SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study
30 PARTS IDENTIFICATION
31 PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08
32 PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08
33 PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT
34 PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT
35 PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08
36 PARTS IDENTIFICATION MANFACTURED 08-07 TO 01-08
37 PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT
38 PARTS IDENTIFICATION MANUFACTURED 02-08 TO PRESENT
39 PARTS IDENTIFICATION MANUFACTURED 08-07 TO PRESENT
4 TABLE OF CONTENTS PAGE FORWARD/WARRANTY……………………………………………………….2 SAFETY INFORMATION……….………………………………………..……..
40 PARTS IDENTIFICATION MANUFACTURED 08-07 TO PRESENT
41 PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08
42 PARTS IDENTIFICATION MANUFACTURED 08-07 TO 01-08
43 PARTS IDENTIFICATION 2000-166 DET QTY PART NO. DESCRIPTION 1 1 2000-533 SPINDLE, CROS
44 PARTS IDENTIFICATION 12-09 TO PRESENT
45 PARTS IDENTIFICATION NOTE: THE LEFT FRONT STUB AXLE HAS THE AMBER REFLECTOR DECAL. 8-07 TO 11-09
46 PARTS IDENTIFICATION
47 PARTS IDENTIFICATION NOTE: CAST HUB CANNOT BE ORDERED SEPARATE, ONLY ITEMS ASSEMBLED TO HUB CAN BE PURCHASED INDIVIDUALLY. PART N
48 PARTS IDENTIFICATION
49 PARTS IDENTIFICATION UPDATED 02/2009
5 GENERAL INFORMATION High capacity with high clearance keeps your planter and or side-dress operation running longer, the perfect answer for bigger
50 PARTS IDENTIFICATION
51 PARTS IDENTIFICATION
52 PARTS IDENTIFICATION
53 PARTS IDENTIFICATION
54 NOTES:
55 NOTES:
56 Our name Is getting known Just a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on
6 ASSEMBLY INSTRUCTIONS Step 1. Attach the axle stubs to the front and rear main axles using the ¾” X 2 ½” hex head bolts and locknuts. Step 2.
7 ASSEMBLY INSTRUCTIONS Step 3. Attach the tire/wheel assemblies to the 8-bolt hubs using the wheel nuts 2520-370. Torque to 100 ft/lbs.
8 ASSEMBLY INSTRUCTIONS Step 4. Insert the 2000-200 hitch drawbar tongue into the 2000-201 hitch receiver and install the ½” x 4-1/2” bolt and lo
9 ASSEMBLY INSTRUCTIONS Step 5. Attach the drawbar assembly to the front axle using 2) 7/8” x 4” bolts and lock nuts.
Comments to this Manuals